Guide

How do you measure a flood cut?

ScopePro · Updated

Measure a flood cut in linear feet along the wet walls, leaving out door openings, then multiply by the cut height to get the square feet of drywall removed. In our practice the cut sits 12–16 inches above the highest wet reading: 2 ft when a few inches of water is found and dealt with quickly, 4 ft when the drywall has had more than 3 days to wick or the water was over 8 inches. In a 12 × 14 ft room with one 3 ft doorway, that's 49 LF: 98 SF at 2 ft, 196 SF at 4 ft.

What a flood cut is

A flood cut is a straight, level cut along the bottom of a wet wall, so the wet drywall below it comes out and the wall cavity can dry. You scope it in linear feet (LF) of wall and square feet (SF) of drywall removed.

Choosing the cut height

Drywall pulls water upward through capillary action, so the wet line in the wall ends up higher than the water ever stood. The cut height comes from moisture readings, not from the water line you can see.

In our practice:

  • The cut sits 12–16 inches above the highest wet reading.
  • 2 ft when a few inches of water is found and dealt with quickly.
  • 4 ft when the drywall wasn't found and cut within 3 days, or the water was more than 8 inches deep.

Readings decide it. Wet, dry and at-risk readings should always be taken with a calibrated moisture meter and interpreted by a qualified field technician or an industrial hygienist. Take readings above your planned cut before you mark it; if the wall reads wet or at risk above the cut, go higher.

Base the height on moisture readings and applicable remediation standards, not carrier preference.

How to measure it

  1. Measure the wet walls in linear feet. For a whole room, that's the perimeter: 2 × (length + width) for a rectangle.
  2. Subtract the doorways. There's no drywall to remove where a door is.
  3. Multiply by the cut height to get the SF of drywall removed.
  4. Count both sides of an interior wall only if both sides are wet.

LF for the scope, SF for the order. Flood cuts are usually scoped in linear feet. The contractor placing the drywall order needs the full square footage, both layers where there are two, so they don't end up with too much or too little board.

Worked example (fictional room)

A 12 × 14 ft room with 8 ft walls and one 3 ft doorway, wet on every wall.

StepCalculationResult
Perimeter2 × (12 + 14)52 LF
Less the doorway52 − 349 LF
Drywall removed at a 2 ft cut49 × 298 SF
Drywall removed at a 4 ft cut49 × 4196 SF
Baseboardsame run as the cut49 LF

The same room doubles its drywall quantity when the cut goes from 2 ft to 4 ft, which is why the height is the decision that matters most in the scope.

Windows: don't deduct them. Most sills sit above a 2 ft cut, and even when a window dips into a 4 ft cut, the piece below it is a few square feet: a 3 ft wide window with a 3 ft sill takes about 3 SF out of the cut. That saves no material; it ends up as scrap. It does add labor, though: cutting and finishing around the sill and the window return takes longer than a straight run, so note the windows that fall inside the cut.

Two layers of drywall

Some walls have two layers, especially in hospitality and multifamily buildings, where fire-rated walls are common. The authority having jurisdiction (AHJ) will often require the seams in the two layers to be offset, so they don't line up.

In practice that means the face layer is cut higher than the layer behind it, even when the water only needs a 2 ft cut: the back layer at 2 ft, the face layer at 3 ft or 4 ft. Scope each layer as its own line. Same room, back layer at 2 ft and face layer at 4 ft:

LayerCalculationResult
Back layer, 2 ft49 × 298 SF
Face layer, 4 ft49 × 4196 SF
Drywall removed, both layers98 + 196294 SF

Check the wall's rated assembly and the AHJ's requirements before you set the heights.

What goes with the cut

A flood cut is rarely the only line in the room. Scope these alongside it:

  • Baseboard: the same LF as the cut.
  • Insulation: exterior walls usually have insulation in the cavity, and the wet part comes out with the drywall. It's the same SF as the cut on those walls. When you put new insulation back, in our practice you fill the cavity with a little more than came out, so the insulation left in the wall above the cut stays supported and doesn't slump.
  • Door casings: in our practice they come off with every flood cut.
  • Cabinet toe kicks: in our practice, these too.
  • Paint, full walls: in our practice, always. A patch painted to the cut line never matches the wall above it, so every wall with a cut gets painted top to bottom. That's a net wall area question: see How do you calculate net wall area?.
  • Texture and finish: scope it. Blending a flood cut so it disappears takes skill, whether the wall has a knockdown texture or a smooth level 4 finish: the new board has to be feathered into the old wall above the cut. Leave it out and the contractor is short on the job; rush it and the room looks obviously repaired.

Look for these before you settle the scope:

  • Cabinet boxes that run to the floor. Some cabinets have no separate toe kick; the box itself sits on the wet floor. If the box is wet, the lower cabinets may have to come out, which can take the countertop with them, and if the uppers have to match, the uppers too.
  • Outlets. Note where they sit relative to the cut, and whether an electrician will be needed to move or replace them.
  • Door bottoms. Look for swelling at the bottom of wood doors.
  • Sandwiched assemblies. Layered materials, such as paneling over drywall, two layers of board, or built-ins against a wet wall, hold water and speed up deterioration. Free them as much as possible so they can dry. Where replacing them isn't feasible, they may be dried in place, always in consultation with an industrial hygienist or a certified Applied Structural Drying (ASD) technician.

Common mistakes

  • Not deducting doorways. No drywall, no cut.
  • One height for the whole job. Rooms that took different water, or sat wet for different lengths of time, can need different cuts.
  • Missing the second side of a wet interior wall. If water reached both sides, both sides come out.
  • Cutting both layers of a two-layer wall at the same height. Offset seams usually mean the face layer goes higher.
  • Measuring the cut but not what rides along. Baseboard, insulation, casings and toe kicks follow the same run.
  • Painting to the cut line. It won't match. Paint the full wall.
  • Leaving texture and feathering out of the scope. It's skilled work, and without it the repair shows.
  • Ordering from the LF. The order needs the full square footage.
  • Guessing the wet line. Take readings with a calibrated meter; wicking can climb higher than you expect.
  • Missing a sandwiched assembly. Layers that trap water keep the wall wet after the cut.

How ScopePro does it

ScopePro turns an iPhone LiDAR scan into each room's floor perimeter and door and window trim in linear feet, plus wall areas, and the PDF scope report lists each door with its width, so subtracting the doorways from the perimeter takes one step. Scope lines are kept by room. ScopePro measures the room; it doesn't detect water, moisture or how far drywall has wicked. Those readings stay yours.

FAQ

Do you measure a flood cut in LF or SF? Both. LF describes the cut along the wall; SF (LF × cut height) is the drywall removed and replaced.

Do you deduct windows from a flood cut? No. The piece below a sill is a few square feet that ends up as scrap, so there's no material saved. Note windows inside the cut for the extra labor of cutting and finishing around them.

What about walls with two layers of drywall? Scope each layer separately. Where the AHJ requires offset seams, the face layer is cut higher than the back layer, often 3–4 ft over a 2 ft back cut.

Why 2 ft or 4 ft? In our practice those are the two standard heights: 2 ft for a little water caught fast, 4 ft when the drywall has had time to wick or the water was deep. In our practice the cut goes 12–16 inches above the highest wet reading.

Do both sides of an interior wall get cut? Only if both sides are wet. Check each side.

Related guides